Differences
This shows you the differences between two versions of the page.
Next revision | Previous revision Next revisionBoth sides next revision | ||
en:clt:hotspot:software:cltdesigner:manual:modul_sherpa_clt_connector [2020/03/23 16:45] – created Alexandra Thiel | en:clt:hotspot:software:cltdesigner:manual:modul_sherpa_clt_connector [2020/03/23 18:02] – [Weitere Systemangaben] Alexandra Thiel | ||
---|---|---|---|
Line 1: | Line 1: | ||
FIXME **This page is not fully translated, yet. Please help completing the translation.**\\ //(remove this paragraph once the translation is finished)// | FIXME **This page is not fully translated, yet. Please help completing the translation.**\\ //(remove this paragraph once the translation is finished)// | ||
- | ====== | + | ====== |
<WRAP center round todo 100%> | <WRAP center round todo 100%> | ||
- | In Bearbeitung! | + | Under construction! |
</ | </ | ||
- | {{ clt: | + | {{ en:clt: |
- | ===== Eingabedaten | + | ===== Input data ===== |
- | Die Eingabe gliedert sich in: | + | The input is divided into: |
- | * Auswahl des Verbindungstyps | + | * selection of the connection type |
- | * Definition der zu verbindenden BSP-Bauteile | + | * definition of CLT elements to be connected |
- | * Wahl der Schraubenlänge | + | * selection of screw length |
- | * Optionen | + | * options |
- | * je nach Verbindungstyp weitere Systemangaben | + | * depending on the connection type further system specifications |
- | * Lastangaben und Bemessungsfaktoren | + | * input of loads and design factors |
- | ==== Verbindungstyp | + | ==== Connection type ==== |
- | {{ : | + | {{ en: |
- | Derzeit stehen folgende Verbindungstypen zur Verfügung: | + | Currently the following connection types are available: |
- | * Eckverbindung | + | * corner connection |
- | * Verbindung | + | * connection |
- | * Verbindung Wand-Decke | + | * connection wall-floor |
- | ^ | + | ^ |
- | |{{ : | + | |{{ en: |
- | ==== Zu verbindende Bauteile ==== | + | |
- | Die zu verbindenden Bauteile werden über den jeweiligen Aufbau definiert. Die Eingabe erfolgt analog zum [[modul_plate1d_continuousbeam# | + | ==== Elements to be connected ==== |
- | {{ : | + | The elements to be connected are defined by the respective layup. The input is the same as for the [[modul_plate1d_continuousbeam# |
- | Sollte aufgrund der Bauteildicke eine Einfräsung notwendig sein, wird ein Warnhinweis angezeigt und, wenn möglich, auch auf eine alternative Schraubenlänge hingewiesen. | + | {{ en: |
- | {{ : | + | If milling is necessary due to the thickness of the elements, a warning message is displayed and, if possible, an alternative screw length is mentioned. |
+ | {{ en: | ||
- | ==== Schrauben ==== | ||
- | Der SHERPA CLT-Connector wird werkseitig am Bauteil 1 (Trägerbauteil) mittels 6 SHERPA Spezialschrauben montiert. Mit weiteren 4 SHERPA Spezialschrauben wird der Bauteil 2 (anzuschließendes Bauteil) angeschlossen. Die Länge der geneigten Schrauben kann je nach Anforderung 100 mm, 120 mm oder 140 mm betragen. | + | ==== Screws ==== |
- | {{ : | + | The SHERPA CLT-Connector is fixed on element 1 (base element) at the factory by using 6 SHERPA special screws. A further 4 SHERPA special screws are used to connect element 2 (element to be connected). The length of the inclined screws can be 100 mm, 120 mm or 140 mm, depending on requirements. |
+ | {{ en: | ||
- | ==== Optionen ==== | ||
- | Zwischen den Bauteilen können Zwischenlagen wie z.B. Kompriband oder Schalldämmlager angeordnet werden. Da der Einbau eines Schalldämmlagers Einfluss auf die Beanspruchbarkeit " | + | ==== Options ==== |
- | {{ : | + | Intermediate layers such as compriband or sound insulation layers can be placed between the elements. Since the installation of a sound insulation layer influences the load capacity "shear force out of plane", |
- | ==== Weitere Systemangaben ==== | + | {{ en: |
- | Im Fall des Verbindungstyps " | + | ==== Further system specifications ==== |
- | {{ : | + | In case of connection type " |
+ | |||
+ | {{ en: | ||
==== Lastangaben und Bemessungsfaktoren ==== | ==== Lastangaben und Bemessungsfaktoren ==== |