Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision |
en:clt:hotspot:software:cltdesigner:manual:modul_sherpa_clt_connector [2020/03/23 17:45] – [Schrauben] Alexandra Thiel | en:clt:hotspot:software:cltdesigner:manual:modul_sherpa_clt_connector [2020/03/24 09:30] – [Lastangaben und Bemessungsfaktoren] Alexandra Thiel |
---|
FIXME **This page is not fully translated, yet. Please help completing the translation.**\\ //(remove this paragraph once the translation is finished)// | FIXME **This page is not fully translated, yet. ** |
| |
====== Module "SHERPA CLT-Connector" ====== | ====== Module "SHERPA CLT-Connector" ====== |
| |
| |
==== Optionen ==== | ==== Options ==== |
| |
Zwischen den Bauteilen können Zwischenlagen wie z.B. Kompriband oder Schalldämmlager angeordnet werden. Da der Einbau eines Schalldämmlagers Einfluss auf die Beanspruchbarkeit "Querkraft aus der Ebene" hat, muss dies über die Option "Schallschutzlager ≤ 12 mm" angegeben werden. | Intermediate layers such as compriband or sound insulation layers can be placed between the elements. Since the installation of a sound insulation layer influences the load capacity "shear force out of plane", this must be indicated via the option "sound insulation layer ≤ 12 mm". |
| |
{{ :clt:hotspot:software:cltdesigner:manual:modul_sherpa_clt_connector:optionen.png |Optionen}} | {{ en:clt:hotspot:software:cltdesigner:manual:modul_sherpa_clt_connector:optionen.png |Options}} |
| |
==== Weitere Systemangaben ==== | ==== Further system specifications ==== |
| |
Im Fall des Verbindungstyps "Verbindung Wand-Decke" sind Wandhöhe und Wandlänge sowie ein Randabstand anzugeben. Bei der Wahl des Randabstandes ist immer auf die Montagetauglichkeit zu achten. | In case of connection type "Connection wall-floor", wall height and length as well as an edge distance must be specified. When selecting the edge distance, always pay attention to the mounting suitability. |
| |
{{ :clt:hotspot:software:cltdesigner:manual:modul_sherpa_clt_connector:weitere_systemangaben.png |Weitere Systemangaben}} | {{ en:clt:hotspot:software:cltdesigner:manual:modul_sherpa_clt_connector:weitere_systemangaben.png |further system specifications}} |
| |
==== Lastangaben und Bemessungsfaktoren ==== | ==== Load data and design factors ==== |
| |
Je nach gewähltem Verbindungstyp sind entweder Lasten (Verbindungstyp "Verbindung Wand-Decke") oder Schnittgrößen (Verbindungstyp "Eckverbindung" und "Verbindung in der Ebene") einzugeben. | Depending on the selected connection type, either loads (connection type "connection wall-floor") or internal forces (connection type "corner connection" and "connection in-plane") must be specified. |
| |
**Verbindungstyp "Verbindung Wand-Decke"** | **Connection type "connection wall-floor"** |
| |
Beim Verbindungstyp "Verbindung Wand-Decke" können eine horizontale und eine vertikale Last (Bemessungswert) angegeben werden. Die benötigte Anzahl der Verbinder sowie die jeweiligen Kräfte auf die einzelnen Verbinder werden unter Einbeziehung der Geometrie und der Randabstände sowie der minimalen und maximalen Abstände untereinander mittels eines [[https://www.holzbauforschung.at/fileadmin/user_upload_CLTdesigner/Download/ExcerptDissFlatscher_GarvicEtAl2015a.pdf|linear elastischen Federmodells]] berechnet. | For the connection type "connection wall-floor", a horizontal and a vertical load (design value) can be specified. The required number of connectors as well as the respective forces on the individual connectors are calculated by means of a [[https://www.holzbauforschung.at/fileadmin/user_upload_CLTdesigner/Download/ExcerptDissFlatscher_GarvicEtAl2015a.pdf|linear elastic spring model]], taking into account the geometry and the edge distances as well as the minimum and maximum distances between them. |
| |
{{ :clt:hotspot:software:cltdesigner:manual:modul_sherpa_clt_connector:lasten.png |Lastangaben}} | {{ en:clt:hotspot:software:cltdesigner:manual:modul_sherpa_clt_connector:lasten.png |Load data}} |
| |
**Verbindungstyp "Eckverbindung" und "Verbindung in der Ebene"** | **Connection type "corner connection" and "Connection in-plane"** |
| |
Bei den Verbindungstypen "Eckverbindung" und "Verbindung in der Ebene" erfolgt die Angabe der Beanspruchung über Schnittgrößen (wirkende Kräfte auf den betrachteten Verbinder). Der Verbinder kann durch eine Normalkraft sowie durch Querkräfte in und aus der Ebene beansprucht werden. Bei den anzugebenden Schnittgrößen handelt es ich um Bemessungswerte. Auf die korrekte Eingabe des Vorzeichens ist zu achten. | For the connection types "corner connection" and "connection in-plane", the action is specified by internal forces (forces acting on each individual connector). The connector can be exposed to a normal force as well as to shear forces in and out of plane. The internal forces to be specified are design values. Make sure that the sign is entered correctly. |
| |
{{ :clt:hotspot:software:cltdesigner:manual:modul_sherpa_clt_connector:schnittgroessen.png |Schnittgrößen}} | {{ en:clt:hotspot:software:cltdesigner:manual:modul_sherpa_clt_connector:schnittgroessen.png |Internal forces}} |
| |
Des Weiteren sind der Modifikationsbeiwert k<sub>mod</sub> und der Teilsicherheitsbeiwert γ<sub>M</sub> anzugeben. | Furthermore, the modification coefficient k<sub>mod</sub> and the partial safety factor γ<sub>M</sub> must be specified. |
| |
{{ :clt:hotspot:software:cltdesigner:manual:modul_sherpa_clt_connector:bemessungsfaktoren.png |Bemessungsfaktoren}} | {{ en:clt:hotspot:software:cltdesigner:manual:modul_sherpa_clt_connector:bemessungsfaktoren.png |Design factors}} |
| |
===== Ergebnisse und Ausgabe ===== | ===== Ergebnisse und Ausgabe ===== |