en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision		 Previous revision
en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam [2020/03/24 12:51] – [Fire] Alexandra Thielen:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam [2024/10/11 11:54] (current) – [Cross section] Alexandra Thiel
Line 1: Line 1:
 ====== Module "CLT-Plate 1D - Continuous beam" ====== ====== Module "CLT-Plate 1D - Continuous beam" ======
  
-{{ en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam:modul_continuousbeam.png?600 |CLT-Plate 1D - Continuous beam}}+{{ en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam:modul_continuousbeam.png |CLT-Plate 1D - Continuous beam}}
 ===== Input data ===== ===== Input data =====
  
Line 34: Line 34:
 If a user-defined cross section is entered, the thickness and orientation of each layer can be changed. Furthermore, the material can be changed for all layers. The thickness of each layer has to be within the range of 6.0 mm to 45 mm. In the case of proprietary CLT products, the strength class of lumber and the orientation can be changed. If the orientation is changed, the whole cross section is rotated. If a user-defined cross section is entered, the thickness and orientation of each layer can be changed. Furthermore, the material can be changed for all layers. The thickness of each layer has to be within the range of 6.0 mm to 45 mm. In the case of proprietary CLT products, the strength class of lumber and the orientation can be changed. If the orientation is changed, the whole cross section is rotated.
  
-{{ en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam:querschnitt.png |Input - Cross section}}+{{ en:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam:querschnitt.png?400 |Input - Cross section}}
  
 The width of the CLT plate strips can be also defined in this field. The default value is set to 1 m. The thickness of the CLT plate is calculated automatically based on the thickness of the single layers. The width of the CLT plate strips can be also defined in this field. The default value is set to 1 m. The thickness of the CLT plate is calculated automatically based on the thickness of the single layers.
Line 53: Line 53:
   * With {{:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam:export_button.png?40&nolink}} the cross sections from the library can be exported to a csv file.   * With {{:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam:export_button.png?40&nolink}} the cross sections from the library can be exported to a csv file.
  
-<WRAP center round info 100%>+<WRAP center info 100%>
 **Syntax of the csv file** **Syntax of the csv file**
  
Line 74: Line 74:
   * With {{:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam:export_button.png?40&nolink}} the materials from the library can be exported to a csv file.   * With {{:clt:hotspot:software:cltdesigner:manual:modul_plate1d_continuousbeam:export_button.png?40&nolink}} the materials from the library can be exported to a csv file.
  
-<WRAP center round info 100%>+<WRAP center info 100%>
 **Syntax of the csv file** **Syntax of the csv file**
  
Line 128: Line 128:
   * > 1000 m   * > 1000 m
   * FIN, IS, N, S   * FIN, IS, N, S
- 
-The span of each field can also be modified in the table of distributed loads. 
  
 Concentrated loads can be entered in the second table. The position can be defined whether by the local or global x-coordinate. Concentrated loads can be entered in the second table. The position can be defined whether by the local or global x-coordinate.
  • en/clt/hotspot/software/cltdesigner/manual/modul_plate1d_continuousbeam.1585050696.txt.gz
  • Last modified: 2020/03/24 12:51
  • by Alexandra Thiel